|
|
| 현재위치 : HOME > PRODUCT > 임베디드컴퓨팅 > 5.25 Form Factor |
|
 |
|
|
|
|
| The ELK-EPC567 is middle-range embedded module with the most wanted Dual LVDS TFT display support, and running VIA C3 CPU up to GHz. It is the new-generation P3 compatible platform built around the DDR memory, the standard now replacing the old SDRAM. The ELK-EPC567 will be the best solution for the new-generation applications like POS, Transaction Terminals, Car PCs, and Kiosks which now always carry rich media or information and need dual flat panel displays. Particularly for the media streaming intensive environments, the ELK-EPC567 will perform well because of the built-in hardware MPEG II playback features. The ELK-EPC567 can support the entire VIA CPU range from the 400 MHZ ultra low power up to 1.2 GHz, or even higher, making this platform flexible in any performance requirements. The ELK-EPC567 will fit any kind of embedded applications because of so many I/O interfaces built onto the board. It comes with SIO x 4, USB 2.0 x 6, IDE x 1, Compact Flash x 1, etc. |
|
|
|
|
| System Architecture |
5.25" Drive Form Factor and PCI V2.2 compliant |
| CPU Support |
On-board VIA C3 Processor EBGA Package with 128KB Level 1 and 64KB Level 2 Cache 1Ghz CPU on board |
| Memory |
One 184-pin DDR SDRAM DIMM. Support Max memory size to 1GB |
| BIOS |
Award system BIOS,
Advanced Configuration & Power Interface support, and 4M bits flash ROM |
| Chipset |
VIA 8623 (CLE266) 100 /133 MHz North Bridge
and
VIA VT8235 |
| LAN |
VIA VT6105 Ethernet Controller x 1,
Single Chip 10 /100 Base TX support, full duplex
,and
90 degree RJ45 connector x 1 |
| Audio |
AC97 ver. 2.0 compliant interface from VT8235 Sound AC-97 Audio Interface
Audio interface (Pin header): Line in, Microphone in, Speaker out (with Amplifier) |
| VGA |
VIA CLE 266 Chipset intergraded Graphic Engine
16/32/64 MB frame buffer shared memory
Full internal AGP 4X performance
Support for resolutions up to 1024 x 768, single pixel, 18 bit LVDS panel
Primary LVDS Interface Connector x 1 (Hirose DF13-20DP x 1)
Secondary LVDS Interface Connector x 1 (Hirose DF13-20DP x 1)
Dual Independent Display Support and
15Pin D-Sub CRT VGA Output |
| Solid State Disk |
Internal CompactFlash socket x 1 |
| I/O interface |
UltraDMA-33/66/100 master mode EIDE controller x 1,
Support Max. ATA100 IDE with 40 pin connector x 1,
SIO x 4, All support RS 232/485 (By Switch Selection),
PIO x 1, bi-directional, EPP/ECP support, 26 pin connector x 1,
8 pins header connector x1(for PS/2 keyboard/mouse),
USB 2.0 port x 6; JST 2.0mm x 3,
Buzzer x 1,
GPIO (4 in 4 out), 3-pin header for SMbus, one pin for GND, CCFL x 2 for LCD Panel Backlight Inverter Power, On Board reset SW and power SW(ATX mode) button (2.54mm), On Board Power LED and HDD Active LED Pin Header (2.54mm)
|
| Real time clock |
On chip RTC with battery back up
and External Li-lon Battery x 1 |
| Watchdog Timer |
Watchdog timeout can be programmable by Software from 1 second to 64 Sec. |
| Bus Expansion |
PC/104-Plus |
| Dimensions |
203mm(L) x 146mm(W) |
Power Source &
Power requirements |
20 pin power input connector (standard ATX connector),
+3.3V is converted from +5V |
| Environments |
Operating temperatures: 0°C to 60°C, Storage temperatures: -20°C to 80°C
Relative humidity: 10% to 90% (non-condensing) |
| Certification |
CE Mark and FCC Class A |
|
|
|
|
|
 |
 |
| ELK-EPC569 |
5.25" embedded board with on-board VIA C3 1GHz CPU |
All specifications within this document are subject to change without notice. |
|
|
|
